BK Radio DPH Bedienungshandbuch PDF herunterladen (Seite 13)

14 BK Radio

While hold time after a reception remains,

transmissions will be in the same mode as the

received signal, regardless of the status of the

‘TX Digital’ soft switch. As in Talkback Scan, the

RTX channel and receive annunciators will be

displayed for the duration of the timer.

The talkback timer can be cleared by making the

held channel invalid. For instance, if a scan

channel is being held, turn scan off.

COMMAND GROUP

The DPH-CMD radio allows construction of a Command Group of up to

20 channels, drawn from any of the programmed channels in the radio.

To modify the Command Group (add or delete channels) all scanning

functions (Channel Scan, Group Scan, and Priority Scan) must be

turned OFF.

BUILDING A COMMAND GROUP

While operating in a group other than the

Command Group (group 1 – 25), the user

selects a channel in the radio and presses the

[*] key. The display will prompt the user to

press the [ENT] key to add the channel into

the Command Group. If a channel is on the

scan list in its home group, it will also be on the

Command Group’s scan list. Unprogrammed

channels cannot be added to the Command

Group. Up to 20 channels may be entered.

After adding a channel, the display

momentarily shows ‘CMND CHAN XX’ where

XX is the channel number (1 – 20).

Parameters associated with each selected

channel, such as Bandwidth, Scan, and Power

settings, are also used while operating in the

Command Group.

Once 20 channels are entered, subsequent

presses of the [*] key, followed by the [ENT]

key, will cause the radio to beep and

momentarily display the message ‘CMND

FULL’. When operating in the Command

Group, the continuously rotating channel

selector will “stop” at the highest programmed

channel.

CMND full

CMND CHAN

CH 12

Press PTT

During Hold Time

(while the ‘RX’

annunciator is lit)

Ent: add chan

* : UNIT CALL

DPH-CMD Owner’s Manual 31

selected. Repeater Talk Around operation will

use the pre-programmed RX NAC.

The UNAC Pick List can be viewed by

pressing [FCN], then [6] ([FCN] then [N]).

The display will show:

NAC – 01

XXXX

To see the NAC displayed in hexadecimal

format, press and hold the [#] key.

NAC – 01

$XXX

To return to the decimal display, press and

hold the [#] key again.

Press [PRI] to increment through the list or key

in a number. Press [ENT] to exit the list

viewer. (This feature is for viewing the list only.

Pressing [ENT] when a list item is displayed

does NOT associate the UNAC with the

selected channel.)

Programming of the list (if programming is not

locked out by PC software) can be

accomplished as follows:

1. While viewing the list, press and hold the

[FCN] key until the ‘PRG’ annunciator

lights.

2. Press [CLR] and then enter the new NAC.

In decimal mode, valid entries are 0 –

4095. The values 3966 and 3967 are

reserved for receivers and cannot be

entered.

In hexadecimal mode, valid entries are $0

- $FFF. The values $F7E and $F7F are

reserved for receivers and cannot be

entered.

To enter hexadecimal characters A - F:

NAC - 01

659

CLR

FCN

PRI

ENT

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 22 23

Kommentare zu diesen Handbüchern

Keine Kommentare

BK Radio DPH Bedienungshandbuch Seite 13

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Radios BK Radio DPH