BK Radio DPH Bedienungshandbuch PDF herunterladen (Seite 18)

26 BK Radio

INITIATING A UNIT-TO-UNIT CALL

To initiate a Unit-To-Unit call, press the [*] key.

The display will prompt you to press [*] again to

enter Unit-To-Unit Mode. The label of the last

active (called or received) ID will appear on the

display.

If the last active ID was a Call List ID, its label

will be displayed along with the bell icon,

otherwise the numeric ID will be displayed along

with the bell and D icon. If a label is displayed,

press and hold [#] to view the corresponding

numeric ID.

To place a call to the displayed unit, press PTT.

To choose another unit, use the keypad to enter

the desired call list entry (0 - 9), or press [PRI]

repeatedly to cycle through all call list entries, or

press [#] to manually key in a new ID (up to 7

digits). To re-select the ‘last active’ ID, press the

[*] key. Once the new unit ID is selected or

entered, press PTT to place the call.

To exit Unit-To-Unit Mode, press and hold

the [*] key.

RECEIVING A UNIT-TO-UNIT CALL

When a Unit-To-Unit call is received while the

radio is in normal Operating Mode, the radio will

beep twice. The display will show the ID of the

calling unit. If the ID matches one of the Call

List IDs, the associated label will be displayed

along with the RX and bell icons. Otherwise the

numeric ID will be displayed along with the RX,

bell, and D icons. The calling unit’s ID will be

displayed for the duration of the reception, and

once the signal goes away, for a programmed

hold time. When the hold time expires, the

display will return to the normal Operating Mode

display, but the bell icon will flash until the [*]

key is pressed twice, putting the radio in Unit-

To-Unit Mode, displaying the last active ID.

LABEL

Last Active Was Unit

On Call List

Prompt For

Manual ID Entr

LABEL

Incoming Call From

ll Li

145

Last Active Was Unit

Not On Call List

CH 5

Missed Call

Incoming Call From

Unit Not On Call List

RX D

145

ENT: ADD CHAN

* : UNIT CALL

DPH-CMD Owner’s Manual 19

When the PTT switch is released, the radio

continues to monitor the selected channel for

the preset scan delay time before it resumes

scanning.

TALKBACK SCAN

If your radio is programmed for Talkback

Scan, press PTT while a channel is active or

while scan delay time remains. You will be

responding on the transmit frequency of the

received channel.

Talkback Scan will not work if Priority Scan is

also on and your radio is programmed to

always transmit on the Priority 1 channel.

CHANGE THE SCAN LIST

If the radio has not been programmed for

Scan List Lock, the user may add or remove

channels from the Scan List. If user changes

are enabled, follow these steps to change the

Scan List:

1. Slide Switches B (scan) and C (priority)

down.

2. Select a channel

to be added or removed

from the Scan List by turning the Channel

Selector knob. If the channel is already on

the Scan List, SCN appears in the display.

3. Press the [ENT] key

to add a channel to

the Scan List. A short beep sounds and

SCN appears in the display.

4. Press the [CLR] key

to remove a channel

from the Scan List. A short beep sounds

and SCN disappears from the display.

GROUP SCAN

Channels on each “Channel Scan List” in

groups on the “Group Scan List” are scanned

sequentially. The selected group is always

scanned when Group Scan is enabled, even if

that group is not on the Group Scan List.

SCN

LABEL 12

1 2 3

7 8 9

CLR

FCN

PRI

ENT

1 2 ... 13 14 15 16 17 18 19 20 21 22 23

Kommentare zu diesen Handbüchern

Keine Kommentare

BK Radio DPH Bedienungshandbuch Seite 18

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Radios BK Radio DPH